Complete iPhone 17 Pro teardown! Replace frame, screen, battery, logic board, cameras, chassis, buttons & USB-C, back cover, then reassemble and calibrate with Repair Assistant.
Buy tools and parts on AMAZON:
Screwdriver Set:
https://hfixt.com/sproPro Toolkit:
https://hfixt.com/toolMagnetic Mat:
https://hfixt.com/matTweezers:
https://hfixt.com/tzrsAliExpress:
Adhesive tape:
https://s.click.aliexpress.com/e/_c2xyKEXlScrewdriver Set:
https://hfixt.com/alisOpening Tool Kit:
https://hfixt.com/alitMagnetic Mat:
https://hfixt.com/amatTweezers set:
https://hfixt.com/altz📌*Useful links*
Best Screwdriver Set:
https://youtu.be/fdtNem4rDDMRepair Tools & Safety Tips:
https://youtu.be/Sp7PhrKV-vQMore DIY repair guides:
https://how-fixit.com📱Follow us for more tech tips and guides!
TikTok:
https://www.tiktok.com/@howfixitInstagram:
https://www.instagram.com/howfixit/Facebook:
https://www.facebook.com/HowFixit/X:
https://x.com/HowFixit*Description*
In this HowFixit guide, I’ll completely disassemble the iPhone 17 Pro so you can replace any failed part: housing, screen, battery, logic board, cameras, Face ID, speakers, Taptic Engine, power/volume/control buttons, antennas, wireless-charging coil and the USB-C charging port. You’ll also see the full reassembly, calibration with Apple’s Repair Assistant, and water-resistance restoration using new adhesive sealing tape.
🔧Tools used: precision screwdrivers (Pentalobe 0.8, Tri-Wing 0.8, T4 Torx, Phillips 1.0, Standoff 1.5), plastic pry tools, tweezers, suction cup, screen disassembly tool, 9-volt battery with clamps (for battery adhesive release), magnetic mat, and adhesive sealing tape.
Chapters below link to every step. If this helped, like & subscribe for more DIY repairs!
🎬Timecodes:
00:00 Intro & what you’ll learn
00:25 Tools & safety
01:14 Power off & remove Pentalobe screws
01:28 Heat display (90 °C / 194 °F) & create gap
03:24 Remove bracket & disconnect display
04:00 Battery plate: remove 14 screws
04:47 Battery removal (9-volt method) & adhesive tips
05:27 Install new battery adhesive
05:41 Face ID module: bracket, disconnect & remove
05:58 Rear cameras: 3 screws, disconnect & lift out
06:34 Earpiece speaker removal
06:53 Logic board: disconnects, coil cable, lift board
07:46 Flash diode & rear mic flex
09:45 LiDAR module removal
10:30 Removing the antenna
11:49 Removing the Taptic Engine
12:56 Bottom loudspeaker removal
13:31 USB-C charging port + lower mic flex removal
16:30 Volume buttons flex: screws & removal
17:05 Power & Control Button flex removal
18:42 Wireless-charging coil & back glass removal options
18:54 Frame/housing swap considerations
19:18 Reassembly best practices (screw mapping, connector cleaning)
33:29 Partial reassembly for boot test
33:51 Repair Assistant calibration (Parts & Service History)
34:16 Functional testing checklist (Face ID, cameras, buttons, audio, charge)
35:30 Restore water resistance: clean, apply new adhesive tape
39:15 Final assembly & closing tips
🌟FAQ:
❓Question: Will I get a “non-genuine part” message after replacing parts?
✔️Answer: Yes, iOS may show a notification in Parts & Service History. It doesn’t block usage; run Repair Assistant and verify functions.
❓Question: Do I need to recalibrate after camera, Face ID or housing changes?
✔️Answer: Yes. Use Repair Assistant via Settings - General - About - Parts & Service History and complete on-screen steps over Wi-Fi.
❓Question: How do I restore water resistance after opening the phone?
✔️Answer: Old adhesive loses sealing. Clean the frame with 91-99% isopropyl alcohol and apply a new pre-cut adhesive gasket before closing.
AFFILIATE PROGRAM
As an Amazon Associate, I earn from qualifying purchases.
#iphone17pro #iphonerepair #teardown #ifixiphone #howfixit