I will show step by step the full process to assemble this ASK14 Glider. I will show some flight video from the maiden flight. This glider has a 2.5 meter wing span and flies very well. Links bellow to all the parts and materials. The STL files can be purchased from Planeprint.com.
Thank you so much for watching!
If you like videos like this, consider buying me a coffee, it really supports me:
https://www.buymeacoffee.com/troymcmillanrcSee what else I am working on:
https://www.instagram.com/troymcmillan_rc/ https://www.tiktok.com/@troymcmillan_rc#3DPrinted,#RCAirplane, #ItFlies
STL Files:
https://www.planeprint.com/ask14How to Print Thin Wall:
https://www.youtube.com/watch?v=TZ_-AespXDw&t=2sArtillery Sidewinder Review:
https://www.youtube.com/watch?v=DDZPZbcnwAs&t=215sProducts Mentioned:
Artillery Sidewinder 3D Printer:
https://amzn.to/396eqIpArtillery Genius 3D Printer:
https://amzn.to/39cA6CZLW-PLA:
https://colorfabb.com/lw-pla-naturalRed PLA:
https://amzn.to/3tjfIt3White PETG:
https://amzn.to/2MvroIxClear PETG:
https://amzn.to/3tmzvrrBlack TPU:
https://amzn.to/2Sw3Oe8CA Glue:
https://amzn.to/2J8EvNWCA Accelerator:
https://amzn.to/3fpbycz3536 1450kv Motor:
https://amzn.to/3aAllu860amp ESC:
https://amzn.to/3rjBMSj9x4 Prop:
https://www.masterairscrew.com2x HS-55 Servos:
https://amzn.to/3oRnDKV4x HS-40 Servo:
https://amzn.to/3m3hnPi2700mah 3S Battery:
https://amzn.to/34ttPjJAR620 Receiver:
https://amzn.to/3j4PbK4DX6 Transmitter:
https://amzn.to/3l6NFsD3pin wire assortment:
https://amzn.to/3l1xNYtXT60 connector:
https://amzn.to/3iyZWnfY-Harness:
https://amzn.to/3jAFwvo5mm magnet:
https://amzn.to/35ZPLoN3mm Steel Rods:
https://amzn.to/39KV8tSLead weight:
https://amzn.to/3cFnzeuScrew assortment:
https://amzn.to/2SvMxSs2mm push rod ends:
https://amzn.to/3nnjD4UZ-Bend pliers:
https://amzn.to/34mA0rtHot knife:
https://amzn.to/3nrCwUHDrill Bits:
https://amzn.to/3nIJzrxCarbon Rods:
https://www.readymaderc.comOnboard Camera:
https://amzn.to/3rp2OrH32mmx25mm Retracts:
https://hobbyking.com/en_us/electric-retract-with-reversible-mount-1pc-18-8g.html?wrh_pdp=2https://hobbyking.com/en_us/servoless-retract-with-metal-trunion-for-small-models-32mm-x-25mm-mount-2pcs.html?wrh_pdp=2https://www.horizonhobby.com/product/e-retract--zero-1100mm/FMMPJ119.htmlhttps://www.horizonhobby.com/product/e-retract-p-51-strega-voodoo/ROHKA122.htmlhttps://www.horizonhobby.com/product/retract--p39-hells-bells-980mm/FMMPI110.htmlhttps://www.horizonhobby.com/product/e-retract-p-39/ROHKG111.html*These are the settings I used for my Artillery Sidewinder 3D Printer. These settings are not going to work with every printer, or every PLA. Printers have different length bodin tubes, and PLA’s have different melting points. These may not work exactly for you, but should give you a good base to start with if you have a similar size printer. Good luck!
Profile 3 Cura Settings:
Quality:
Layer Height – 0.25
Line Width – 0.4
Shell:
Wall Line Count – 1
Infill:
Infill Density – 0
Material:
Printing Temperature – 230
Build Plate Temperature – 60
Flow – 100
Enable Retraction – Checked
Retraction Distance – 1.3
Retraction Speed – 10
Retraction Extra Prime Amount – 0.3
Speed:
Print Speed – 100
Outer Wall Speed – 35
Inner Wall Speed – 35
Travel Speed – 80
Travel:
Combing Mode – off
Cooling:
Enable Print Cooling – Checked
Fan Speed – 50
Mesh Fixes:
Union Overlapping Volumes – NOT Checked
Special Modes:
Surface Mode – Surface
Experimental:
Slicing Tolerance – Middle
Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!!