Building 5inch FPV drone with Walksnail Moonlight and LED lights

Thanks to JLC3DP for sponsoring this video!
JLC3DP 3D printing service starts at $0.3, Get $60 Coupons for New Users: https://jlc3dp.com/?from=Skipta

This time i'm going to build a 5" FPV Drone with Walksnail Moonlight on board. But I'm also going to install LED lights on this quad.
This build is my most complex build so far. But there's more to come! I've already started working on a 3.5" FPV drone. So stay tuned.

I have a playlist with all my build videos there:
https://www.youtube.com/playlist?list=PLiz-pk1IBnKhD6CkFZ57MnX_FRMYY2VaD

In this build i used (affiliate links):
Frame - GepRC Mark5 Analog
(https://geprc.com/product/geprc-gep-mk5-frame/?ref=Skipta)
Motors - GEPRC SPEEDX2 2107.5 1960KV
)https://geprc.com/product/geprc-speedx2-2107-5-1960kv-2450kv-motors/?ref=Skipta)
Propellers - HQ Freestyle Prop 5X4.3X3V2S
(https://www.hqprop.com/hq-freestyle-prop-5x43x3v2s-2cw2ccw-poly-carbonate-p0233.html)
FC+ESC - GOKU F722 Pro V2 55A
(https://www.mepsking.shop/flywoo-goku-f722-pro-v2-55a-32bit-128k-stack.html?inviterId=1870043504758616066&utm_source=affiliate&utm_medium=affiliate&spec=F722 PRO V2 55A AM32 128K Stack)
Video - Walksnail Moonlight
(https://caddxfpv.com/products/walksnail-moonlight-kit?ref=Skipta&srsltid=AfmBOop3C1sX_rvKvJbXX0hOJaBoQC2gD9u64LO3A5lVCz220_1pp8Qi)
Radio - Radiomaster XR3 Nano
(https://www.mepsking.shop/xr3-nano.html?inviterId=1870043504758616066&utm_source=affiliate&utm_medium=affiliate&spec=2 x 2.4GHz)
GPS - Beitian BE122
(https://store.beitian.com/products/beitian-gps-module-with-antenna-ubx-m10050-gnss-chip-ultra-low-power-gnss-receiver-for-track-be-126-be-166-be-220-be-280-be-880?variant=44369390371103&srsltid=AfmBOoqBC0S0gZB8NhMATPc9gnqoCJxET1NdTQVQDd83SNZGj5EXw4QN)
Batteries - Ovonic 6S 1300mAh
(https://collabs.shop/cj1nda)
3D prints is here:
(https://www.thingiverse.com/thing:7010312)


0:00 Unpacking
0:40 Frame assembling
4:35 Flight Controller and ESC installation
8:25 Motors preparation
12:15 3D printing with JLC3DP
12:57 Motors installation and soldering
18:25 ESC Conformal coating
19:16 Walksnail Moonlight installation
18:25 ESC Conformal coating
20:43 LED lights soldering
22:46 FC Conformal coating
23:35 Radiomaster RP4TD soldering
25:05 GPS preparation
26:08 Buzzer
26:32 Assembling with 3D printed parts
27:48 XT60 soldering
28:42 Assembling
34:22 check for short
35:44 3D printing with JLC3DP
36:14 Final assembling